![]() Any pointers for Spy Hunter steering would be appreciated though. Even have an aimtrak light gun for gun games as well. I also have a tankstick with trackball and a spinner (Turbo Twist 2 with a 5" wheel) for games like tempest and All Points Bulletin. My 3 pedal setup and shifter came today, so I'll replace the 2 pedal setup with those items. Now that I know this is normal I will work around it and add the brake pedal back into the inputs. I actually have most steering wheel games working (270 degree wheel), just not the brake pedal. Just seems strange that the joy 1 throttle does not work this way, only the brake pedal. Just needed the reassurance that this is all normal. Well aware of MAME and how/the need to configure inputs and analog controls. I was referring to PS4 games, not other MAME games. My hope is that this is trivial, but if not I have a 3 pedal set on order that I hope will not suffer the same fate as I would love to be able to brake properly so I can finally get 1st place on Ace Driver. And even tried to configure it using a third party tool all to no avail. I have tried playing with sensitivity in MAME. Then never use brake in games cause it will brake to 100% always as the button is not analog.Ĭracking open the pedal case and playing with the pedometer (sp?) this fixes it temporarily, but then jacks up PS4 or other games that are not MAME. So I shove cardboard under the pedal to half press it to stop the scrolling and just assign a brake to a digital button. ![]() I do not set the brake in MAME because it just causes weird problems being half pressed like this. To remedy this I must half press the brake pedal (setting the axis back to 0) so I can actually use the keyboard down key to navigate the UI to set other controls. However in MAME, if I hit "tab" to configure inputs and press the brake pedal, the cursor scrolls infinitely down as if the keyboard down button is constantly pressed. Full press gives full press, and letting off the pedals restore pressure to 0. In the Windows test tool for Thrustmaster T150 both pedals work as expected showing no pressure applied to pedals until pressed. The cheap ones, I have a 3 pedal set on order because of the problem I'm about to describe. I have a 2 pedal setup from Thrustmaster for a T150 steering wheel. Device is now working properly with no other changes other than using a USB 2.0 port.Apologies in advance, I have not found a solution to this problem. This is the service that is being launched - Įdit 3: Found a thread where someone said their wheel only worked in USB 2.0 ports.and that worked for me. I attempted to have it launch in Administrator + compatibility mode, but that did nothing. It immediately launches when the wheel is plugged in. But when I attempt to update the firmware, it can't.Įdit 2: This is the process that once killed will allow the control panel to open. The firmware updater also can see the wheel now, and also shows version 0. Even more bizzarely, my firmware is showing 0. The control panel shows the wheel turning and its position, brake and gas being pushed as well as all the buttons.but when I go to test forces and click on any of them, they do nothing. I got the control panel to open - there was a thrustmaster process that seemed to be hogging up the wheel, killing it then allowed the control panel to open. I updated the firmware (I received it on firmware 31, and the most recent is 34) and hoped that would fix it, but seems to have done nothing.Įdit: Issue just keeps getting weirder. I plugged it in to my laptop with Windows 10 and was immediately able to get the Thrustmaster Control Panel working.genuinely the first time in months on Windows 11 that I've had an issue like this. I've spent several hours researching and poking around to no avail, so I'm a bit stuck. The wheel inputs do work, just with no force feedback (when I go into ACC, I can apply throttle/brake and steer).Īny suggestions would be massively appreciated. I tried running it in Windows 8 compatibility to no avail (I'm running Windows 11, which others have said is supported). I'll click on the "Control Panel" icon, and it'll open the "Game Controllers" Windows panel, I'll click on "Properties", but then the window freezes, and the Thrustmaster Control Panel never loads. I want to use it with my PC for now to play ACC, but I can't get the Thrustmaster Control Panel to load. Hi all, as the title says, I bought a T300 RS (non GT, so no clutch) and my PS5 is currently out of commission.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |